Benefits:
- Ideal for dry processing zones such as food packaging zones
- Contains Polygiene, an antimicrobial additive based on silver ion technology
- Very high chemical resistance Easy to clean and sterilise – minimal joints
- Non-tainting, non-dusting
- High abrasion resistance
- Low odour during application
FeRFA Resin Flooring guidelines
Description:
Applied in two or more coats. Generally solvent or water borne.
Duty:
light foot traffic, occasional rubber tyred vehicles.
Typical Thickness:
up to 150 µm
Description:
Applied in two or more coats. Generally solvent free.
Duty:
light foot traffic, occasional rubber tyred vehicles/regular foot traffic, frequent fork lift truck traffic, occasional hard plastic-wheeled trolleys
Typical Thickness:
150 µm to 300 µm
Description:
Applied in two or more coats. Generally solvent or water borne.
Duty:
lregular foot traffic, frequent fork lift truck traffic, occasional hard plastic-wheeled trolleys
Typical Thickness:
300 µm to 1000 µm
Description:
Aggregate dressed systems based on multiple layers of floor coatings or flow-applied floorings, often described as ‘sandwich’ systems.
MD/HD
Duty:
regular foot traffic, frequent fork lift truck traffic, occasional hard plastic-wheeled trolleys/constant fork lift truck traffic, hard plastic wheeled trolleys, some impact
Typical Thickness:
> 2 mm
Description:
Often referred to as ‘self-smoothing’ or ‘self-levelling’ flooring and having a smooth surface.
Duty:
regular foot traffic, frequent fork lift truck traffic, occasional hard plastic-wheeled trolleys/constant fork lift truck traffic, hard plastic wheeled trolleys, some impact
Typical Thickness:
2 mm to 3 mm
Description:
Trowel-finished, heavily filled systems, generally incorporating a surface seal coat to minimize porosity.
Duty:
regular foot traffic, frequent fork lift truck traffic, occasional hard plastic-wheeled trolleys/constant fork lift truck traffic, hard plastic wheeled trolleys, some impact
Typical Thickness:
> 4 mm
Description:
Having a smooth surface.
Duty:
constant fork lift truck traffic, hard plastic wheeled trolleys, some impact/severe heavily loaded traffic and impact
Typical Thickness:
4 mm to 6 mm
Description:
Trowel-finished, aggregate filled systems effectively impervious throughout their thickness.
Duty:
severe heavily loaded traffic and impact
Typical Thickness:
> 6 mm
Project References:
Food: Nestlé; Mars; McVities; Courage Brewery; Grants Whisky; also meat, fish and drinks industries.
Pharmaceutical: Astra Zeneca; Pfizer; Levers; GlaxoSmithKline; Bayer and many more.
Product: Pagefresh MF Finish: Matt
Thickness: mm (4 or 6 mm)
Preparatory work and application in accordance with suppliers instructions.
The figures that follow are typical properties achieved in laboratory tests at 20°C and at 50% Relative Humidity.
Reaction to fire BFL – s1 EN 13501-1
Wear Resistance Abrasion quantity <1 cm3 EN 13892-5 Bond Strength > 2.5 N/mm2 EN 13892-8 Impact Resistance 15 Nm EN ISO 6272
Coefficient of Thermal Expansion
5.70 x 10-5
mm/mm°C
ASTM C531
Compressive Strength 55 N/mm2 EN 13892-2
Flexural Strength 20 N/mm2 EN 13892-2
Tensile Strength 7 N/mm2 BS 6319-7
Temperature Resistance Tolerant to intermittent spillages up to 70°C
or sustained heat from -20°C to 60°C
Water Permeability Nil – Karsten Test (impermeable) Vapour Permeability ASTM E96:90
5 g / m2 / 24hrs (at 4 mm thick)
Chemical Resistance Contact Technical Department
Excellent resistance to sugars and most acids (organic and inorganic)
Slip Resistance
Method described in BS 7976-2
(typical values for 4-S rubber slider)
Dry >40 low slip potential
(in accordance with HSE and UKSRG guidelines)
The slipperiness of flooring materials can change significantly, due to the
installation process, after short periods of use, due to inappropriate maintenance, longer-term wear and/ or surface contaminants (wet or dry).
Textured systems are recommended to meet slip resistance value requirements for wet conditions and/ or surface contaminants (wet or dry)
– please contact our Technical Advisors for further details and specifications.
Complies with BS 8204-6/FeRFA type 7.
Concrete or screed substrate should be a minimum of 25N/mm2, free from laitance, dust and other contamination. The substrate should be dry to 75% RH as per BS8204 and free from rising damp and ground water pressure. If no damp proof membrane is present Pageseal DPM can be incorporated directly beneath the Pagefresh MF system.
Products Included in this System
Primer: Pageprime @ 0.25 kg/m2
OR, where a dpm is required,
Pageseal DPM @ 0.5 kg/m2
OR, where high heat resistance is critical,
Pagefresh Primer @ 0.25 kg/m2
Topping: Pagefresh MF (density 1.9 kg/l)
@ 7.6 kg/m2 for 4 mm
@ 11.4 kg/m2 for 6 mm
Note:
Pagefresh MF must always be applied onto a primed surface. Pageprime is suitable for general use, but Pagefresh Primer should be used if the area is exposed to heat (above 50°C) or hot liquids (above 60°C).
Pagefresh MF is a self-sealing finish.
Detailed application instructions are available upon request.
Pagefresh MF is not colour fast and may change colour over time (exhibits a yellowing effect). Colour change depends on the UV light and heat levels present and hence the rate of change cannot be predicted. This is more noticeable in light colours and blues but does not compromise the product’s flexibility or chemical resistance characteristics. We have endeavoured to adopt colours within our standard range which minimise this change.
Intensively coloured products (e.g. hair colorants, medical disinfectants etc.) and plasticizer migration (e.g. from rubber tyres) can lead to irreversible discoloration in the surface.
Please contact our Technical Services Department for further advice.
The Polygiene antimicrobial additive incorporated into Pagefresh MF provides control of most bacteria and fungi which come into contact with the floor.
Antimicrobial Active substance: Silver biocide Tested: ISO 22196/JIS Z2801.
| 10°C | 20°C | 30°C | |
| Light traffic | 36 hrs | 12 hrs | |
| Full traffic | 72 hrs | 48 hrs | |
| Full chemical cure | 10 days |
The finished system is assessed as non-hazardous to health and the environment. The long service life and seamless surface reduce the need for repairs, maintenance and cleaning.
Environmental and health considerations are controlled during manufacture and application of the products by Pagecrete staff and fully trained and experienced contractors.
Aftercare – Cleaning and Maintenance
Clean regularly using a single or double headed rotary scrubber drier in conjunction with a mildly alkaline detergent.
Page’s products are guaranteed against defective materials and manufacture and are sold subject to its standard Terms and Conditions of Sale, copies of which can be obtained on request.
Any suggested practices or installation specifications for the composite floor or wall system (as opposed to individual product performance specifications) included in this communication (or any other) from Pageconstitute potential options only and do not constitute nor replace professional advice in such regard. Page recommends any customer seek independent advice from a qualified consultant prior to reaching any decision on design, installation or otherwise.
